5050 RGB8路LED灯驱动（IO驱动，STM32）
一、前期准备
单片机：STM32F103ZET6
开发环境：MDK5.14
库函数：标准库V3.5
RGB LED模块：淘宝有售
二、实验效果
8种颜色的LED流水灯，分配见下表，0代表Disable，1代表Enable
R G B
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
PWM驱动方式
三、驱动原理
模块上面的RGB引脚低电平有效，LED灯IO口也是低电平有效。
需要完整工程或者有问题的请加QQ：1002521871，验证：呵呵。
四、驱动代码
led.h
#ifndef __LED_H__
#define __LED_H__
#include "stm32f10x.h"
#include "gpio.h"#define LED_R PEout(0)
#define LED_G PEout(1)
#define LED_B PEout(2)#define RGB_LED1 PGout(8)
#define RGB_LED2 PGout(9)
#define RGB_LED3 PGout(10)
#define RGB_LED4 PGout(11)
#define RGB_LED5 PGout(12)
#define RGB_LED6 PGout(13)
#define RGB_LED7 PGout(14)
#define RGB_LED8 PGout(15)extern void LEDConfiguration(void);
#endifled.C
#include "led.h"void LEDConfiguration(void)
{ GPIO_InitTypeDef GPIO;//Enable APB2 BusRCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOE | RCC_APB2Periph_GPIOG, ENABLE);//Register IO GPIO.GPIO_Pin = 0x07;GPIO.GPIO_Speed = GPIO_Speed_50MHz;GPIO.GPIO_Mode = GPIO_Mode_Out_PP;GPIO_Init(GPIOE, &GPIO);GPIO.GPIO_Pin = 0xff00;GPIO.GPIO_Mode = GPIO_Mode_Out_PP;GPIO.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOG, &GPIO);LED_R = OFF; LED_G = OFF; LED_B = OFF; RGB_LED1 = OFF; RGB_LED2 = OFF;RGB_LED3 = OFF; RGB_LED4 = OFF;RGB_LED5 = OFF; RGB_LED6 = OFF;RGB_LED7 = OFF; RGB_LED8 = OFF;
}APP.c
#include "app.h"void ShowRGBLEDs(void)
{uint8_t i = 0;uint8_t times = 50;//RGB : 001LED_R = OFF;LED_G = OFF;LED_B = ON;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 010LED_R = OFF;LED_G = ON;LED_B = OFF;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 011LED_R = OFF;LED_G = ON;LED_B = ON;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 100LED_R = ON;LED_G = OFF;LED_B = OFF;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 101LED_R = ON;LED_G = OFF;LED_B = ON;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 110LED_R = ON;LED_G = ON;LED_B = OFF;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);//RGB : 111LED_R = ON;LED_G = ON;LED_B = ON;for (i = 8; i < 16; i ++){GPIOG->ODR = 0xff00 & (~(1 << i));DelayMs(times);}DelayMs(times);
}由于作者能力有限，有不妥之处欢迎指正，邮箱alex_hua@foxmail.com
本文来自互联网用户投稿，文章观点仅代表作者本人，不代表本站立场，不承担相关法律责任。如若转载，请注明出处。 如若内容造成侵权/违法违规/事实不符，请点击【内容举报】进行投诉反馈！